SATO - Windows printer driver

Driver version 4.6.69.3619

Updates:

• Removed the ability to disable descenders on barcodes EAN13, EAN8, UPC A and UPC E.

Driver version 4.6.69.3612

Updates:

• Driver update didn't preserve settings for all installed printers. This is fixed now.

Driver version 4.6.69.3592

What's new:

• Added support for GS1 Databar UCC/EAN 128

Driver version 4.6.69.3591

Updates:

• GS1 Databar Expanded now prints correctly

Driver version 4.6.69.3583

What's new:

• Vector fonts removed for SBPL mobile printers.

Driver version 4.6.69.3571

What's new:

• Added new USB PnP IDs for CT400, CT410 and CT420 printer models

Driver version 4.6.69.3550

What's new:

• Added support for GS1 Databar

Driver version 4.6.68.3560

Updates:

• Wrong data content when printing form Pocket NiceLabel

Driver version 4.6.67.3556

Updates:

• Fixed issue with tear off mode accidentaly turning on Multidrop functionality even on printers that didn't support it resulting in extra characters in stream.

Driver version 4.6.67.3555

Updates:

• MicroQR now prints correctly

Driver version 4.6.67.3540

What's new:

• When the printer buffer was full and user put the printer in error mode, driver started sending data to the printer again. This was corrected now, so no data will be sent.

Driver version 4.6.67.3532

Updates:

• Fixed issue with prompted variables missing in export

Driver version 4.6.67.3530

What's new:

• Maximum print speed for Sato CG412 is 4 inch per second.

Driver version 4.6.66.3455

What's new:

• Speed range for CGxx printers increased up to 6 inch per second.
  Darkness range B supoprt added to CG4xx models

Driver version 4.6.66.3445

Updates:

• Fixed occasional spooler crash when downloading graphics or fonts to printer

Driver version 4.6.66.3436

Updates:

• Obsolete monitor.inf files were removed from drivers that still had them

Driver version 4.6.66.3435

What's new:

• "Last label eject" option is added for DR308e printer.

Driver version 4.6.66.3392

What's new:

• Removed warning message for special ports, when installing printer driver with Printer Installation Wizard.
  
  If connected to standard Windows TCP/IP port then show warning message.

Driver version 4.6.65.3360

Updates:

• Printer error detailes were missing while printing. The status reporting issue was limited to NicePrintQueue, Enterprise Print Manager(EPM) and NiceLabel.

  
  

Driver version 4.6.64.3303

What's new:

• SATO CG Triumvirate and CG Times fonts had character spacing disabled. This is supported now also on these two fonts.

Driver version 4.6.64.3290

What's new:

• Advanced TCP/IP port monitor now supports connections to names as well as IP addresses.

Driver version 4.6.64.3287

What's new:

• New RFID tags supported for SATO CG208, CG212, CL408e and CL412e :
  PJM StackTag (Magellan)

  
  

  PJM ItemTag (Magellan)

  
  

  PJM Light StackTag (Magellan)

  
  

   

Driver version 4.6.64.3254

Updates:

• Very slow printing when bidirectional printing is turned on.

Driver version 4.6.63.3241

What's new:

• Get From Printer command corrected on LAN port.

Driver version 4.6.63.3224

Updates:

• Rotation option on userinterface and QR and MicroQR barcode font rotation now work correctly

Driver version 4.6.62.3192

What's new:

• Even if 01, 02 dot specification of min module width dimension is valid, it may not be read by the scanner, but there are customers that can confirm it is readable at his place.
  The same is for 01, 02, 03 dot specification of min module vertical dimension.

Driver version 4.6.62.3190

Updates:

• Spooler crash when changing printer port while printing was fixed.

Driver version 4.6.62.3156

Updates:

• Custom settings for unprintable now work correctly

Driver version 4.6.60.3048

Updates:

• Delete format command corrected.

Driver version 4.6.59.3002

Updates:

• Printer ports are now properly shown in Options dialog.

Driver version 4.6.59.2995

What's new:

• Changed font for Chinese Windows to SimHei.

Driver version 4.6.55.2911

What's new:

• SATO GY412T double side printer is supported now. It is called GN412T in Japanese market.

Driver version 4.6.51.2900

What's new:

• Added PCX compression option to SATO printers

Driver version 4.6.51.2811

What's new:

• Alternate escape sequance influence also on Store settings command (PG). In this case caret is send instead of escape (0x5E instead of 0x1B).

Driver version 4.6.51.2800

What's new:

• Czech, Lithuanian and Ukrainian languages are now supported also in all NiceDrivers.
  
  

Driver version 4.6.50.2773

Updates:

• When printing from standard Windows application (like Microsoft Word) and using page rotation (Landscape and/or rotate 180), positions of graphic were shifted relative to internal elements.
  Shift size depends on page dimensions, shift direction depends on rotation.
  

Driver version 4.6.49.2747

What's new:

• PrnInst utility was updated so that long INF file structure is supported.

Driver version 4.6.49.2611

Updates:

• When trying to preinstall drivers on Windows 7, user got an "Environment incorrect" error message. This is corrected now.

Driver version 4.6.48.2715

What's new:

• New month format MMM is supported now for printers SATO S84xx, LT408 and M84xxse.

Driver version 4.6.48.2645

What's new:

• Added Aztec and GS1 Datamatrix barcodes. GS1 Datamatrix barcode works from NiceLabel version greater than 5.2.2865. Please check also your printer's firmware version if support these barcodes.

Driver version 4.6.45.2515

Updates:

• Corrected PG command (Store Settings) on CG4 printers for Thermal Transfer option.
  Thermal Transfer is now 00(hex) and Direct thermal is now 01(hex) - opposite as it was before.

Driver version 4.6.45.2421

Updates:

• Commands <ESC>A, <ESC>EX0, <ESC>AR and <ESC>A3 have been missing when printing on CG4x printer. This is corrected now.

Driver version 4.6.44.2501

What's new:

• Tag-it HF-I (Sirit module) tag removed for CG2 printers.

Driver version 4.6.43.2445

What's new:

• User is now able to change administrator settings without reopening driver properties dialog as an elevated user. A click on the shielded button and entering the credentials is all that is needed.

Driver version 4.6.42.2404

Updates:

• Thermal transfer option is not disabled anymore on CG2 printer models.
  Button for changing printer mode (SBPL, PCL) is removed as this option is not supported on CG2 printer.

Driver version 4.6.41.2378

What's new:

• Japanese translation update.

Driver version 4.6.41.2364

Updates:

• Fixed occasional driver crash when printing extremely large graphics

Driver version 4.6.41.2361

What's new:

• Page preview icons in "Advanced Dialog" corrected.
  

Driver version 4.6.37.2258

Updates:

• Uninstall of printer with Printer Install Wizard did not work on Windows 2003 (x64) system

Driver version 4.6.34.2259

Updates:

• Export to printer functionality was updated so that data length is included for barcode CODE-93.            

Driver version 4.6.30

What's new:

• New SATO printer models:
  TG308
  TG312
  CG208
  CG212
  CG408
  CG412

Driver version 4.6.24

Updates:

• Sato M84Pro 600 dpi models does not support EX0 command.

Driver version 4.6.22

What's new:

• Build number is now part of version information in About dialog

Driver version 4.6.14

Updates:

• Download graphics to PCMCIA slot didn't work. This is fixed now.

•  SATO LM4xxe printers can print  1249 mm long labels.

Driver version 4.6.07

Updates:

• Store & Recall is disabled for SATO CX printers.
• Corrected USB PnP ID for SATO MB410i.
• There was not possible to export to SAP from labeling software if UPC-A barcode was present on the label. This is corrected now.

Driver version 4.6.06

Updates:

• Buffer overflow error occured when printing big pages of graphics through USB

Driver version 4.6.03

What's new:

• Additional Date pictures ware added for SBPL printers:
  MM DD YYYY, MM-DD-YYYY, MM.DD.YYYY and MM/DD/YYYY can be used as internal Date format.

Driver version 4.6.01

Updates:

• Added Rotation to parsed text in command fonts

Driver version 4.6.00

Updates:

• Printing process was stopped during heavy duty printing.
• Additional date pictures are added into the driver for SATO: just month, just day, just year, combination of day+month, week of the year (ww)

Driver version 4.5.50

What's new:

• SATO DR308e printer is added into Nice driver distribution.

Driver version 4.5.42

What's new:

• Driver print speed optimization

• Additional PnP ID's for CT400 printer model.
  LPT: LPTENUM\SATO_CT4005372

  
  

  USB: USBPRINT\SATO_CT4005372

  
  

   

Updates:

• Optimization - Empty lines in graphics are skiped on all SATO printers

• When user changed the protocol type of the printer and driver, status reporting stopped working.

Driver version 4.5.41

Updates:

• Enhanced SBPL printers can use also negative left/top offset values from Advanced setup driver dialog.

Driver version 4.5.39

What's new:

• SATO M-8465Se is also supported model.

Updates:

• PrnInst showed login window, even if the user running the application was administrator.

Driver version 4.5.38

Updates:

• On some old SATO models like CX are human readable is not internaly supported on EAN8, EAN13 and UPC-A printers. So in this case driver always sends the human readable. Driver sends HR for below printer models.
  All CX models,M-5900,M-5900RV,M-8400/6,M-8400/8,M-8400RV,M-8400S,M-8450,M-8459S,M-8460S,M-8460S OH,M-8485S,M-8485S OH,M-8490S,M-8490S OH

Driver version 4.5.37

Updates:

• PrnInst can now be moved to any position (second monitor) and it will stay there. It will not jump back to its original position.

• SATO DR308e printers also needs A1 command for correct alignment. SATO DR308e StartDoc escape is the same as for GT printers. There was missing A3 command for offset and STX ESC+A with ESC+Z ETX arround speed command <CS>.

Driver version 4.5.36

Updates:

• Internal HR presentation for barcode UPC-a is not valid.
• SATO DR308e supports also vector fonts like SATO GT408e model.

Driver version 4.5.34

Updates:

• Postnet barcode fonts can no longer have their width changed.

Driver version 4.5.33

What's new:

• Updated Plug and Play information for Sato M10e printer.

Updates:

• Gen2 tag on Sato didn't work right.

Driver version 4.5.32

What's new:

• New PnP Id added for Sato M-5900RVe printer

Driver version 4.5.31

Updates:

• Immediate command on SATO CX models (Advanced Setup > Other) sends also Print Mode parameter (CP0 for direct or CP1 for transfer mode) when sending SesorType, Test or Status option.

Driver version 4.5.13

Updates:

• Change speed command valu calculation for "M84 Pro 200 dpi" and "M84 Pro 300 dpi".
  There is send command like CS{"speed in inch/2"}.

• QR barcode position was not correct if using 90 or 270 degree rotation. This is corrected now.

Driver version 4.5.12

What's new:

• USBPRINT PnP ID's have been added for three SATO models: SATOS8408, SATOS8412 and SATOS8424.
  

Updates:

• Print direction is wrong on Sato MB200i. This is corrected now.
• User can select Automatic or Manual options for Job removing using keyboard in Printer Install Wizard
• Fixed labeling software crash when turning off "Use Advanced printer driver interface".

Driver version 4.5.11

What's new:

• Missing printers added to SatoPort distribution. These printers are MB200i, MB201i, MB400i and MB410i.

Updates:

• Printer Install Wizard uninstallation of driver doesn`t remove all of the files from the SYSTEM32\spool\drivers\w32x86\3\ folder.

• Implemented Internal Counter on MBxxx and MBxxxi Legacy printers

• When printing internal MSI barcode it is printed too large compared to graphic barcode. This is corrected now for all SBPL printers.
• User data for EPC Gen2 RFID has not been sent to the printer. This is corrected now.

Driver version 4.5.10

Updates:

• Internal MicroPDF now prints correctly
• "Calibrate" button on Immediate dialog has been renamed into "Send" and moved up, since it relates just Sensor Type and not to the whole page.
• Changed EAN13, EAN8 and UPCA to use internal interpretations.

• Fixed Overlay printing for MB printer models.

• When doing export to printer with XML variant then command <ESC>*F,n should not be present in print stream. This is true for all RFID printer models.
• The list of internal fonts has been changed on some SATO printer models:
  - LM4xxe printers: Vector fonts are added in the list but scalable CGTriumvirate and CGTmes have been removed from the internal font list
  - S84 and CX4xx printer models support also vector fonts
  
• Also SATO S-84xx printers support XML export.

Driver version 4.5.09

Updates:

• Electonic Article Survailance was always disabled on Rfid printers
• Fixed printing of Datamatrix and QR barcode font with more then 255 character data
• Added automatic termination character for Maxicode barcode font data
• Fixed EAN13, EAN8, UPC A and UPC E to not print guides when they should be disabled

Driver version 4.5.07

What's new:

• M10e printer models has now PnP ID .

• Added support for custom printer name after silently installing a printer driver from command line (/INSTPRN; /INSTMULTPRN)

Driver version 4.5.06

What's new:

• Printer Installation Wizard will be able to automaticly remove all jobs when updating printer

Driver version 4.5.05

What's new:

• Printer Install Wizard can start an application specified in the command line, after it closes.

Updates:

• Export to printer didn't work if there were graphics on the label. This is fixed now.

Driver version 4.5.04

Updates:

• Updated PnP IDs for Lt408, CT408i, CT412i, CT424i, S-8408, S-8412 and S-8424 models
• Chinese (Simpl.) translation for "Tear-off" was too long and therefore it wasn't displayed completely on the PG dialog.

Driver version 4.5.03

What's new:

• Status monitor is able to detect port conflicts, when two printer drivers are using the same port for bidirectional communication with the printer.
  Also when user will delete or install a new printer to the system, Status Monitor will detect the change by itself.

Updates:

• When you disable the option "Use advanced printer driver interface" (in File -> Label Setup -> Printing tab) labeling software will crash with the error "GDI Failure, OK to continue?"

Driver version 4.5.02

What's new:

• New printer Sato DR308e printer was added.

Updates:

• PrnInst didn't set printer attributes correctly. This is fixed now.

Driver version 4.5.01

What's new:

• Turkish language added

Updates:

• PG command for Control Code was the same for Standard and Non-Standard.

Driver version 4.5.00

What's new:

•  - write MMF to alternative location (research)
   - update MemMaster to store files to this location
   - update driver to read from new location (make sure that the update will be backward compatible)

Driver version 4.4.73

What's new:

• Max print length was corrected for Sato CLxxx printers.

Updates:

• Uninstall of driver package failed when running a 64bti system.

Driver version 4.4.72

Updates:

• Delay was added after Cancel before print command.

Driver version 4.4.71

Updates:

• The redundant commands in GL driver (ESC+EX and ESC+AR) have caused some problems. Now they are removed from the driver because memory slots are different on this model. (there is no overlay and expanded memory)

Driver version 4.4.70

Updates:

• If you open Settings dialog from Advanced Setup dialog, than some settings are disabled for some printers.

• Fixed font selection for CTxxxi printers

Driver version 4.4.69

What's new:

• Checkbox "Enable bidirectional support" (Printer properties -> Ports) can now be unchecked automatically during driver installation, corresponding to the flag "Bidirectional" in .inf file.
  Bidirectional=0  =>  checkbox is unchecked.
  Bidirectional=1  =>  checkbox is checked.
  If this information is ommited, Bidirectional=1 is assumed.

Updates:

• Labelling software can now recall variables with more than 31 characters of data.

• When you click on the Help button in About dialog help is opened, but it is not linked to any page.

• Help on About dialog opens help page with contents 'This program cannot display the webpage'.

Driver version 4.4.68

Updates:

• Upper speed limit for S8412 is now 14 ips. Before that it was 16 ips.

Driver version 4.4.67 Beta

Updates:

• Download commands for single-byte fonts contained incorrect char info. Character code FF was sent twice. This is corrected now.

Driver version 4.4.66

Updates:

• CG Times and CG Triumvirate fonts are supported also on SATO XL(e) printers.
• ">" Character is no longer encoded as "~" character in barcodes

Driver version 4.4.64

What's new:

• 2 new Sato printers are supported:
  - D508
  - D512

Updates:

• Removed Help button as no help is available.

• CG Times and CG Triumvirate vector fonts can be resized now separately in both directions: (x or y)
• Sato Vector fonts:
  SATO Vector,
  SATO Vector O,
  SATO Vector I,
  SATO Vector OI,
  SATO VectorF,
  SATO Vector OF,
  SATO Vector IF,
  SATO Vector OIF
  
  
  

  have problems with enlargement step. The size of the font on the screen did not rise constantly but there ware illogical steps. This is corrected now.

• Sensor type selection added as Immediate setting for CX models
• New Japanese translation for Printer Install Wizard

Driver version 4.4.63

Updates:

• When user starts Printer Install Wizard the application is shown but without focus
• Fixed sending data to printer on Windows 2000

• Corrected Date and Version in WDM driver INF files
  Corrected WDM folder locations

• Changed default number for cutting to 1 label instead of 0.

• PnP ID's are changed for below RFID SATO printers:
  CL408e UHF
  CL412e UHF
  CL608e UHF
  CL612e UHF
  

Driver version 4.4.62

What's new:

• PnP ID's had to be added to the followin Sato printers:
  CL408e, CL412e, CL608e, CL612e, M-8459Se, M-8460Se, M-8485Se, M-8490Se, XL 400e, XL 410e, M-10e, M84 Pro 200DPI, M84 Pro 300DPI, M84 Pro 600DPI, GT408e, GT412e, GT424e, CT408i, CT412i, S-8408, S-8412, S-8424, MB200, MB201i, MB400, MB400i, MB410i, LM408e, LM412e
• Changed Plug & Play IDs for Sato M-84Pro printers.

Updates:

• Sato CLxxx models do not have support to write the Rfid data in HEX format
• Vector fonts "SATO CG Times" and "SATO CG Triumvirate" are not printed correctly when resized only horizontaly or only verticaly.
• There were only 4 settings for Darkness range (A-D) on on printer preferences dialog (Advanced tab -> Other).
  The missing 2 (E, F) are added now.
• Installation of wdm driver is not working on Windows Vista systems

Driver version 4.4.60

What's new:

• Changed file info for Printer Install Wizard

Updates:

• Fixed port monitor not allowing USB connections

• Removed help button as help is not available.
• Default value for Always use default settings is not correct when instaling it the driver with a configuration file attached.

Driver version 4.4.53

Updates:

• Barcode HR was missing on some models because wrong font was used for representation. This is corrected now.
• Sato GL4xxe printers have a possibility to print 2500mm long labels.

Driver version 4.4.52

What's new:

• DLL files for user interface translation did not include version info data.

Updates:

• Labels transfered from different systems now retain their driver settings.

Driver version 4.4.51

Updates:

• Increased lenght for filename and path in import and export of settings.
• POSTNET barcodes have a fixed height and width, but the interface allows the user to change these dimensions. 

Driver version 4.4.50

Updates:

• Import and export didn't work if filename and path exceeded the length of 80 characters while windows support 256 character lengths
  
• Click on "Stocks" panel caused error if stock list was empty. This is fixed now.

Driver version 4.4.41.0

What's new:

• PrnInst searches for Prn64.bin in current folder as well as in .\Win64 folder.

Driver version 4.4.30

What's new:

• - support for preinstall on all supported platforms

Driver version 4.4.01

Updates:

• Corrected sending Label Dimension to the printer.
• EndDocument escape was sent even when there was no StartDocument.
• If driver gets no separator character description for decimal number from the OS, driver puts a "+" or "," string as default character. The result was seen for page size (example)
  Now the dot character "." is set for default separator in this case.
  

Driver version 4.4.00

What's new:

• Corrected darkness range for S-84xx printers.
• Invalid stocks are now marked. User can open the Stock properties dialog and press OK to fix the problem (which is usually stock dimension). Stock size will be automatically adjusted.

Updates:

• There was missing MicroQR barcode parameter for setting mode. Now this setting is added for MicroQR and also for QR barocode. There was no printout for MicroQR before the correction.
• UI for commands fonts works now properly also in Japanese language.
• When using "Export to Printer" function in labelling software some characters are appended to barcode interpretation. This happens on fixed encoded barcodes (CODE128, GS1-128, SSCC, ...).
  
• In some rare cases streams sent to the printer had an extra "0" added in it.
• On Enhanced printers (CL4xxe, GT4xxe) the command for store format "YS" should be send before the command for paper size "A1". On GL4xxe printers the command for paper size (A1) is added when exporting the label to printer.

Driver version 4.3.73

What's new:

• Store/Recall added for Sato printers
• Added rfid HEX support for some HF printers

Driver version 4.3.72

Updates:

• Sometimes a print stream is not send to the printer, and it stays stuck in the spooler

Driver version 4.3.63

What's new:

• DD/MM/YYYY, DD MM YYYY, DD-MM-YYYY, DD.MM.YYYY date formats was added to Sato printers.
• CT420 printer added to Sato Nice distribution.
  Corrected speeds for CT420 and max print length for CT400 & CT410.

Updates:

• There was a bug present because for below models the command for 2-color printing has been sent to the printer but they do not support this functionality.
  Command "2C0" or "2C1" is removed for models:
  - CL408e UHF
  - CL412e UHF
  - CL608e UHF
  - CL612e UHF
  - M-8459Se UHF
  - M-8460Se UHF
  - M-8485Se UHF
  - M-8490Se UHF
  - M-8460Se OH UHF
  - M-8485Se OH UHF
  - M-8490Se OH UHF
  - CL408e U-Code
  - CL412e U-Code
  - CL608e U-Code
  - CL612e U-Code
  - M-8459Se U-Code
  - M-8460Se U-Code
  - M-8485Se U-Code
  - M-8490Se U-Code
  - M-8460Se OH U-Code
  - M-8485Se OH U-Code
  - M-8490Se OH U-Code
  - S-8408
  - S-8412
  - S-8424
  - GT408e UHF
  - GT412e UHF
  - GT424e UHF
  - GL408e UHF
  - GL412e UHF
  - S-8408 UHF
  - S-8412 UHF
  - S-8424 UHF
  - M-8465Se UHF
  This command can be only used on MB models.
• Port monitor crashed when setting up port details (IP and port number)

Driver version 4.3.62

Updates:

• Print speed correction handling in the print stream for LM4xxe printers.
  

Driver version 4.3.60

Updates:

• Barcode fonts vanished instead of being imported.

Driver version 4.3.59

Updates:

• Microsoft Vista operating system is not mentioned in the text file that is distributed with the driver.
• Red area function was not working correctly. New driver release enables user to correctly define red area sections. In the list red area position is now displayed in selected units.
  
• Some SATO GL4XXe printer specific fonts have been corrected in a way that different command is sent to the printer. So instead of sending to the printer commands WBa,WLa,XBa,XLa now it is sent WB1,WL1,XB1,XL1. Also the font names are corrected from WBa,WLa,XBa,XLa into WB,WL,XB and XL.
  Another change has been done for fonts X20,X21,X22,X23,X24 and this can be seen from print file. Before correction the print stream looks like data, but now it looks like ,data. So the comma has been added between font command and actual data.
  
• Stocks were not imported if user didn't view the stocks dialog beforehand

Driver version 4.3.57

Updates:

• Changed PDF417 barcode command and print darkness command, CG fonts added, Print speed and darkness defaults set to 3. Speed range set to 3-4.

Driver version 4.3.56

Updates:

• GL printer was not working on LAN using SATO port
• Barcode ratio values are not shown in Barcode Fonts dialog. This only happens when you are editing existing barcode font.

Driver version 4.3.55

Updates:

• Spooler crashed during the installation, if there were any printers allready installed on the system.

Driver version 4.3.54

Updates:

• While installing a printer driver on certain systems the spooler crashed.
• "delete" button was enabled even if the barcode/command fonts list was empty. This is fixed now.
• Export of barcode fonts didn't work properly unless user clicked on barcode fonts tab before exporting them. This is fixed now.
• Increased timeouts for better printer status response times
• Slow printing occurred when a Not Accessible printer was found on a network. Printer status was also not received immediately.

Driver version 4.3.53

What's new:

• Sato GL printer models darkness changed. Now user can set values from -15 to 15
  Some controls that have no influence on the drivers functionality are grayed out.

Updates:

• Status for printers (that use bidirectionaal communication) was not correct when the printer was not physicaly connected to the computer. Status was changing between Not Accessible and Ready

Driver version 4.3.52

What's new:

• Sato GL printers have two memory slots for download:
  - Cartridge
  - Internal flash - has been added now
• Epc Gen2 is implemented for GL printers
  Gl printers now support XML export. Label name is also stored in printer memory
  

Updates:

• Sato GL printers support also vector fonts CG Times and CG Triumvirate.

Driver version 4.3.51

What's new:

• Driver can now override the default document settings of some applications with driver default settings (set up in printer spooler)

Updates:

• Incorrect commands (garbage in stream) were sent to the printer when user was exporting to XML.
• Sato CL 408 used to print some blank labels if the label contained graphics very close to the bottom edge. This is fixed now.

Driver version 4.3.07

Updates:

• After viewing the Help file CHM file was locked and because of that reboot was needed to complete the installation. New version of driver will not lock the CHM any more and because of that reboot is not needed.

Driver version 4.3.06

What's new:

• GL printers printers added.
• Speed and darkness settings corrected for GL models
• Barcode fonts and command fonts are now stored in registry.

Updates:

• Changed PnP ids to correct ones
• Corrected XML export to printer for SATO MB2xxi/4xxi printers
• Printing did not work on nonbidirectional printers. Printer Error was displayed the whole time

Driver version 4.3.05

Updates:

• For some 300dpi and 600dpi models OCR-A and OCR-B font is corrected:
  These SATO models have correction:
  MB410i
  M84 Pro 300DPI
  M84 Pro 600DPI
  TDP43H
  TDP46H
  LM412e
  CT412i
  CT424i
  S-8412
  S-8424
  GL412e
  GL412e UHF
  S-8412 UHF
  S-8424 UHF
  
• Printing did not work when bidirectional was enabled

Driver version 4.3.04

What's new:

• New Port monitor is added to the distribution
• On Windows Vista there is warning displayed if user doesn't have appropriate permissions to create (or write to) certain driver files.
• Old HLP help file format was exchanged for new CHM file format.
• MicroPDF barcode type is supported on SATO printers.
  But you need a labeling software version 5.0.1 for using this feature.

Updates:

• When user changed printer's port, the printing was no longer possible until reboot.
• Port monitor now uses correct (64 bit) interface file on 64bit systems.
• Installation did not go through when upgrading from old printer driver, if the user had the driver connected to the Advanced Port Monitor (LAN)
• Bug fixed, where some changes on stocks updated default umprintable area values.

Driver version 4.3.03

Updates:

• Spooler crashed, if user had multiple bidirectional printers using the same port, while using a status monitoring application

Driver version 4.3.02

Updates:

• Stocks were not imported properly or were not shown immediately after import.

Driver version 4.3.01

What's new:

• Korean language added.

Updates:

• Driver does not show all stocks in 'Stocks' combo box on 'Options' dialog. Missing stocks have heights that are near the maximum printer's limit.

Driver version 4.3.00

Updates:

• Changed window handling so that port monitor setup windows can appear on Vista

Click here to download NiceDriver!